Aluminum or steel trapezoidal 35/207 sheeting – direct from the manufacturer

  • Steel or aluminum trapezoidal sheeting
  • Individual design in RAL colors
  • Aluminum sheet thickness: 0.5 mm, 0.7 mm, 0.8 mm, 1mm
  • Steel sheet thickness: 0.5 mm, 0.75 mm
  • Primarily used as roofing sheets in the construction of sheds and stables
  • Can also be used as wall cladding when mounted in the crest profile

We are here for you.

Let us advise you.

+49 (4222) 9421-0
+49 (4222) 9421-22
dachundwand@schuette-aluminium.de

The advantages of our trapezoidal 35/207 sheeting

Our trapezoidal 35/207 sheeting is characterized by its above-average service life. In the crest profile, it can also be used as wall cladding.

Its outstanding structural qualities enable greater purlin spacing, which means that wider spans can be achieved with fewer purlins.

Discover the versatile properties and advantages of our trapezoidal profiles for yourself.

Long service life

Resistant to ammonia, industrial atmosphere, sea air, algae and moss.

 

Highly customizable

Choose from different finishes and RAL colors.

 

Versatile application possibilities

Can be used as roof and wall cladding.

 

100% recyclable

Climate-friendly and with lower environmental impact (high eco-balance).

 

Stainless

Thanks to multi-layer surface finishing.

 

Fire-proof and break-proof

High strength despite the low weight.

 

Trapezoidal 35/207 profile in aluminum or steel

Since we produce the trapezoidal 35/207 profile in steel and aluminum, you can choose the right material for you depending on the application.

“Made in Germany” quality direct from the manufacturer

As a direct manufacturer and specialist for high-quality trapezoidal sheeting “made in Germany”, we have a large stock of different RAL colors, sheet thicknesses and finishes. You can also source compatible accessories from us.

Get competent advice now from our specialists!

 

“Made in Germany” quality direct from the manufacturer

As a direct manufacturer and specialist for high-quality trapezoidal sheeting “made in Germany”, we have a large stock of different RAL colors, sheet thicknesses and finishes. You can also source compatible accessories from us.

Get competent advice now from our specialists!

Our standard RAL colors

Possible thicknesses and lengths of trapezoidal 35/207 sheeting

COLOURSRAL ALUALUALUALUSTEEL*STEEL*STEEL*
Strength: 0,5mmStrength: 0,7mmStrength: 0,8mmStrength: 1,0mmStrength: 0,5mmStrength: 0,63mmStrength: 0,75mm
stuccoxon requeston request
moss green6005on requeston requestx
chrome oxide green6020on requeston requestx
anthracite gray7016xon requeston requestxx
red-brown8012on requeston requestxxx
gray white9002on requeston requestx
brilliant metallic9006xon requeston requestx
gray aluminum9007xon requeston request

Increase the service life of your trapezoidal sheeting with coatings

In contrast to steel, aluminum trapezoidal sheeting is basically stainless, but contact corrosion can still occur if the aluminum comes into contact with another metallic component. The long-term consequence would be a loss of stability and bearing capacity. That’s why high quality in terms of color coating and material processing is important. We are happy to advise you in detail.

Our coatings for trapezoidal sheeting at a glance:

  • 25 µm polyester
  • 35 µm matt polyester
  • 35 µm structured polyester (wood look)
  • Stucco
  • Other coating methods available on request

Anti-condensation & anti-drone membrane

Condensation may form on the underside of roofs profiled with trapezoidal sheeting. The water can drip down and cause long-term damage. Our anti-condensation membrane absorbs the condensation water, which then evaporates naturally.

Anti-drone membrane

This membrane coating also has a noise-inhibiting effect, for example due to rain or hail. Contact us! We are happy to advise you on technical feasibility!

Wide range of applications for our trapezoidal 35/207 sheeting

  • As roofing sheets in the construction of sheds, and in industrial and commercial construction
  • As roofing sheets for barns and stables
  • As wall cladding in the crest profile

Trapezoidal 35/207 sheeting accessories

It goes without saying that you can source all compatible accessories for your trapezoidal sheeting from us – we offer you a one-stop service:

  • trims and flashings,
  • flat sheets
  • and fastenings.

Installation instructions for aluminum trapezoidal sheeting

  • A wooden substructure is suitable for aluminum trapezoidal sheeting.
  • The trapezoidal sheets are attached to the construction with saddle washers.
  • We recommend mounting with domes due to aluminum’s (heat) expansion behavior.
  • Standard fittings can break or loosen over time.
  • To ensure weather resistance, it should always be laid in an overlapping manner.

Installation instructions for steel trapezoidal sheeting            

  • Steel trapezoidal sheeting does not stretch very much.
  • Recessed bead installation with conventional drilling screws can be carried out without any problems.
  • These screws represent a high cost advantage over the use of stainless steel screws.

Download assembly instructions as PDF here

Aluminum or steel trapezoidal sheeting in manufacturer quality

The quality of our products is important to us.

  • The production of our trapezoidal 35/207 sheeting is subject to high quality standards and all profiles bear the CE seal of approval.
  • They are certified according to DIN EN 1090-E EXC3.

We will also be happy to send you our certificates on request.

Our references

  • Trapezbleche aus Alu & Stahl – Schütte Aluminium

    Trapezoidal sheeting project in Iceland – profile 35/207

    2,200 m²

  • Trapezbleche aus Alu & Stahl – Schütte Aluminium

    Trapezoidal sheeting project in Iceland – profile 35/207

    2,200 m²

Trapezoidal sheeting for use as roofing sheets in the construction of sheds and stables, and in industrial and commercial construction

Our trapezoidal 35/207 profile is the most economical among the flat profiled sheets and is mainly used as roofing sheets in the construction of sheds and stables, as well as in industrial and commercial construction.

 

Trapezoidal 35/207 sheeting can also be used as wall cladding

In the crest profile, however, 35/207 can also be used as wall cladding. Its outstanding structural qualities enable greater purlin spacing, which means that wider spans can be achieved with fewer purlins.

Trapezoidal sheet aluminum or steel compared

In terms of stability as well, trapezoidal 35/207 sheeting will impress you with its compelling properties. This trapezoidal profiled sheeting is available in aluminum and steel.

Aluminium

Due to the flexibility of the material and the low weight, aluminum trapezoidal sheeting is significantly easier and faster to process and assemble than steel sheeting.

 

Steel

In turn, steel trapezoidal sheeting is less expensive and does not expand as much with fluctuations in temperature.

 

Not sure which material is best to use for your construction project?

Get direct advice from the experts now.

 

Contact

Do you have any questions? We are here for you.